Another part of the iproute2 software package, ip rule is the single tool for manipulating the routing policy database under linux (RPDB). For a fuller discussion of the RPDB, see Section 10.3, “Using the Routing Policy Database and Multiple Routing Tables”. The RPDB can be displayed with ip rule show. Particular rules can be added and removed with (predictably, if you have been reading the sections on the other iproute2 tools) ip rule add command and the ip rule del command. We'll make a particular example of the ip rule add nat.
Briefly, the RPDB mediates access to the routing tables. In the overwhelming majority of installations (most workstations, servers, and even routers), there is no need to take advantage of the RPDB. A single IP routing table is all that is required for basic connectivity. In more complex networking configurations, however, the RPDB allows the administrator to programmatically select a routing table based on characteristics of a packet.
Along with this freedom and flexibility comes the power to break networking in strange and unexpected ways. I will reiterate: IP routing is stateless. Because IP routing is stateless, the network architect, planner or administrator needs to be aware of the issues involved with using multiple routing tables.
For a fuller discussion of some of these issues, be sure to read Section 10.3, “Using the Routing Policy Database and Multiple Routing Tables”. Now, let's look at some of the ways to use ip rule.
To display the RPDB, use the command ip route show. The output of the command is a list of rules in the RPDB sorted by order of priority. The rules with the highest priority will be displayed at the top of the output.
Example D.28. Displaying the RPDB with ip rule show
There are some interesting items to observe here. First, these are the three default rules in the RPDB which will be available on any machine with an RPDB. The first rule specifies that any packet from any where should first be matched against routes in the local routing table. Remember that the local routing table is for broadcast addresses on link layers, network address translation, and locally hosted IP addresses.
If a packet is not bound for any of these three destinations, the
kernel will check the next entry in the RPDB. In the simple case
packet bound for 220.127.116.11 would first pass through the local
routing table without matching any of the local destinations. The
next entry in the RPDB recommends using the main routing table to
select a destination route.
isolde's main routing
table, it is likely that there is no host nor network match for this
destination, thus the packet will match the default route in the
main routing table.
FIXME!! Can anybody (somebody?) explain to me why there is a rule priority 32767 which refers to table 253? I'm still confused about this.
Adding a rule to the routing policy database is simple. The syntax of the ip rule add command should be familiar to those who have read Section D.2, “ip route” or have used the ip route to populate routing tables.
A simple rule selects a packet on the the packet's characteristics. Some characteristics available as selection criteria are the source address, the destination, the type of service (ToS), the interface on which the packet arrived, and an fwmark.
One great way to take advantage of the RPDB is to split different
types of traffic to different providers based on packet
characteristics. Let's assume two network connections on
masq-gw, one that is a
highly reliable high cost connection, and a much lower cost less
reliable connection. Let's also assume that we are using Type of
Service flags on IP packets on the internal network.
We might want to prefer a low-latency, highly reliable link
for one type of packet. By using
tos as a
selection criterion with ip rule we can
effectively route these packets via our faster and more reliable
Example D.29. Creating a simple entry in the RPDB with ip rule add 
Note that the rule we inserted was added to the next available
higher priority in the RPDB because we did not specify a priority.
If we wished to specify a priority, we could use
Now any packet with an IP ToS field matching 0x08 will be routed according to the instructions in table 8. If no route in table 8 applies to the matched packet (not possible, since we added a default route), the packet would be routed according to the instructions in table "main".
The selection criteria for matching a packet can be grouped. Let's look at a more complex example of ip rule where we use multiple selection criteria.
Example D.30. Creating a complex entry in the RPDB with ip rule add
Frankly, that's a very complex rule! I do not know if I could describe a scenario where this particular rule would be required. The point, though, is that you can have arbitrarily complex selection criteria, and multiple rules which lookup routes in as many of the 253 routing tables as you wish.
ip rule add, while a powerful tool, can quickly make a routing table or router too complex to easily understand. It's important to try to design and implement the simplest configuration to maintain on your router. If you cannot avoid using multiple routing tables and the RPDB, at least be systematic about it.
As discussed more thoroughly in Chapter 5, Network Address Translation (NAT), this is the other half of iproute2 supported network address translation. The two components are ip route add nat and ip rule add nat.
ip rule add nat is used to rewrite the source IP on packets during the routing stage. Each packet from the real IP is translated to the NAT IP without altering the destination address of the packet.
NAT is commonly used to publish a service in an internal network on a public IP. Thus packets returning to the public network need to be readdressed to appear with a source address of the publicly accessibly IP.
Example D.31. Creating a NAT rule with ip rule add nat
In more complex situations, entire subnets can be translated to provide NAT for a range of IPs. The example below shows how to specify the ip rule add nat to complete the NAT mapping in Example D.22, “Creating a NAT route for an entire network with ip route add nat”.
Example D.32. Creating a NAT rule for an entire network with ip rule add nat
Notice the ip rule synonym for the
nat option. It is valid to substitute
Naturally, no iproute2 tool would be complete without the ability to undo what has been done. With ip rule del, individual rules can be removed from the RPDB.
It is at first quite confusing that the word
the ip rule show output needs to be replaced with
the network address 0/0. I do not know why
not acceptable as a synonym for 0/0, but you'll save yourself some
headache by getting in the habit of replacing
By replacing the verb
add in any of the command
lines above with the verb
del, you can remove the
specified entry from the RPDB.
Example D.33. Removing a NAT rule for an entire network with ip rule del nat
The ip rule utility can be a great boon in the manipulation and maintenance of complex routers.
 Please note that this is an incomplete example. Simply put, I'm not dealing with the issues of inbound packets or packets destined for locally connected networks in this example. Keep in mind the instructional nature of this example, and plan your own network accordingly. For a fuller discussion of the issues involved with handling multiple Internet links, see Section 10.4, “Multiple Connections to the Internet”. Note also, that there is no corresponding network connection in the example network for this network connection.